10 Tall Swing Set - 4 Bay - 8 Rubber Belt Swing Seats

NOTE: the photo of this product is the H106 which has one less top rail/middle frame/entire bay than the H108 which this product listing is for. We will update this listing with a more accurate photo when possible. _________________   ________________ __________________ / I                            /                                /                              / I B AA A                     D C                           D C                       A   AA B This set is very heavy duty.  Each bay is designed for two children up to 12 years old, per ASTM and CPSC guidelines.  If installed according to installation instructions, our sets will more than meet these requirements. Actual weight limits depend upon how the set is installed, the amount of concrete, the type of dirt in which the set is installed, how much use, etc.  Therefore, we do not state weight limits for our swing sets. This frame is for an in ground 3 bay heavy duty 10’ high set. You will need to specify colors for the End Frame Fittings, Middle Frame Fittings, Swing Chain and the Commercial Swing Seats.  This product should last 2 years in harsh conditions and up to 5 years in optimal conditions. Some conditions may require replacement sooner. TOOLS AND PARTS NEEDED: Ladder, ¾” wrench, Ratchet socket wrench, Tape measure, A5750 supplied Allen wrench for shackles, and 6mm Allen wrench for set screws, Stakes for marking holes, Shovel, Bricks, Gravel, Wheelbarrow for mixing concrete, Water, Concrete, Trowel, Level, Warning signs. Protective surfacing according to ASTM F1292 for a fall height of 10’. PARTS INCLUDED ARE: A3000 – 2 green or red                          A7600 – 16 blue, green, red or yellow A3025 – 2 green or red                          Pipe Legs A – B - 12.5’ - 4 A2014 – 12                                           Pipe Middle End Legs AA - 12.5’ - 2 A5700 – 12                                           Pipe Middle Legs C – D - 12.5’ - 4 A5750 – 1                                             Top Rail 10’ - 4 A1600 – 8 black, blue, green, red, tan or yellow MEASUREMENTS FOR SWING FRAME: The Front (A) and Back (B) legs are 110” apart above ground and 128” below ground. Lengthwise, the two front legs (A) to (A) are 505” apart. The two middle legs (AA), which are the legs furthest apart, are 582” apart. The front leg (A) to the middle leg (AA) is 72.5” apart above ground. The front leg (A) to the middle front leg (C) is 126” apart. The height of the set is 10’. **INSTALLATION, SAFE USE & MAINTENANCE INSTRUCTIONS** IMPORTANT: To keep children safe from harm, follow these precautions and instructions when installing, using, or maintaining this playground equipment. You can also call us at 1-800-433-2573 for more information or see https://www.cpsc.gov/cpscpub/pubs/324.pdf . Installation: Read all instructions before attempting assembly. To determine proper use zones needed for swing set consult Figure 23, Table 7 for c ommercial swing sets. For residential sets see spacing dimensions on Page 4 of the Outdoor Home Playground Safety Handbook. Install swing set where a child can easily be supervised.   Do not install playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Install your play equipment on level ground with adequate surfacing and anchoring. Use proper hardware, and tighten all connections. Lay out all the pipes and end frame fittings on the ground about two feet from where you have determined you want to place your swing set.   Do not dig holes until frame is assembled, as there may be some variance in leg spacing. Lay an end frame fitting on one end, then a top beam, then a middle frame fitting, then a top beam, then a middle frame fitting, the